Achtung: Your browser is outdated. Please note that Gunfinder may not work properly in some places. You should update your browser as soon as possible. Learn more here!

XLR STEEL WEIGHTS FOR BUFFER TUBE - SET OF 4

≈ $90
Price at the dealer: 81.50 €. Converted at the ECB rate as of November 20, 2026.
No permit required (18+)
31015 Conegliano, Italy
0
ID: 10050394
Purchase from outside the EU: The firearm goes through an importer in your country, the dealer handles the export. How buying from Europe works
Shop safely with Gunfinder
Our AI-powered seller identity verification makes Gunfinder the safest marketplace online. Learn more
About the seller
Armeriaregina
Dealer

Details

Original language
Italian
Category
Condition
New
Location
🇮🇹 31015 Conegliano, Italy
Availability
In stock

Freshness

This listing is based on a mirrored offer, where the listing data was synced to us from a shop, dealer, or external marketplace. Please note that temporary price discrepancies may occur due to possible delays in data transmission.
Source
Armeriaregina
Last checked with the dealer
1 day ago

Description

Note: The item is located abroad. Please note that delivery conditions, shipping times, and/or the purchase process may differ.
The steel weight kit for the buffer tube consists of 4 steel weights weighing 127.5 grams (5.5 ounces) each. The stackable weights allow you to adjust the firearm’s balance point. Depending on the configuration, the weight added to the rear of the firearm can range from 127.5 to 623 grams.

NOTE: Not compatible with Carbon stocks

WEIGHT: Standard / contoured buffer tube capacity: 4 weights (623 grams - 22 ounces)

WEIGHT: Short buffer tube capacity: 3 weights (467 grams - 16.5 ounces)

INSTALLATION INSTRUCTIONS

CONTOURED TUBE: For the contoured buffer tube, assemble the weights and insert them into the tube with the threaded end facing outward. Do not install the O-ring until you have reached the desired weight. Install the included long screw through the rear of the buffer tube and into the steel weights to secure them to the tube. Once you have reached the desired weight, lightly grease the O-ring and install it in the outermost square groove.

STANDARD / SHORT TUBE: For the standard and short buffer tubes, assemble the weights and insert them into the tube with the threaded end facing inward. The standard and short tubes are threaded ¼-20 at the rear. Do not install the O-ring until you have reached the desired weight. Install the included short screw in the rear of the outermost weight. You will need to use a wrench to thread the bolt into the tube. Once you have reached the desired weight, lightly grease the O-ring and install it in the outermost square groove. (Show description in original language)
Il kit di pesi in acciaio per buffer tube è composto da 4 pesi in acciaio da 127,5 grammi (5,5 once). I pesi impilabili consentono all'utente di regolare il punto di equilibrio dell'arma. Il peso aggiunto alla parte posteriore dell'arma può variare da 127,5 a 623 grammi a seconda della configurazione.

NOTA: non compatibile con le calciature Carbon

PESO: capacità buffer tube standard / sagomato 4 pesi (623 grammi - 22 once)

PESO: capacità buffer tube corto 3 pesi (467 grammi - 16,5 once)

ISTRUZIONI PER L'INSTALLAZIONE

TUBO CONTOURED: per il buffer tube sagomato, i pesi devono essere assemblati e inseriti nel tubo con la parte filettata rivolta verso l'esterno. Non installare l'o-ring prima di aver raggiunto il peso desiderato. Installare la vite lunga in dotazione attraverso la parte posteriore del tubo buffer e nei pesi in acciaio per fissarli al tubo. Una volta raggiunto il peso desiderato, ingrassare leggermente l'o-ring e installarlo nella scanalatura quadrata più esterna.

TUBO STANDARD / CORTO: per il buffer tube standard e corto, i pesi devono essere assemblati e inseriti nel tubo con la parte filettata rivolta verso l'interno. I tubi standard e corti sono filettati ¼-20 sul retro. Non installare l'o-ring finché non si è raggiunto il peso desiderato. Installare la vite corta in dotazione nella parte posteriore del peso più esterno. Per infilare il bullone nel tubo è necessario utilizzare una chiave. Una volta raggiunto il peso desiderato, ingrassare leggermente l'o-ring e installarlo nella scanalatura quadrata più esterna.

Similar listings