Double Alpha Academy DAA Alpha-X / Race Master Insert Block Assembly (Magnetisch), Pistoolmodel: Para Ordnance
81,31 €
Vrij verkrijgbaar vanaf 18 jaar
50197 Zaragoza, Spanje
0
ID: 10618626
Aankoop van buiten de EU: Het wapen gaat via een importeur in jouw land; de dealer zorgt voor de uitvoer.
Zo verloopt de aankoop uit Europa
Veilig kopen met Gunfinder
Onze AI-gestuurde identiteitsverificatie van verkopers maakt Gunfinder tot de veiligste marktplaats online.
Meer weten
Details
- Originele taal
- Spaans
- Categorie
- Staat
- Nieuw
- Locatie
- 🇪🇸 50197 Zaragoza, Spanje
- Beschikbaarheid
- leverbaar
Actualiteit
Dit aanbod is gebaseerd op een aanbiedingssynchronisatie, waarbij de aanbiedingsgegevens vanuit een shop, handelaar of extern platform naar ons zijn overgedragen. Houd er rekening mee dat door mogelijke vertragingen bij de gegevensoverdracht tijdelijke prijsafwijkingen kunnen optreden.
- Bron
- Shooting Zaragoza
- Laatst bijgewerkt
- ongeveer 22 uur geleden
Beschrijving
Opmerking:
Het artikel bevindt zich in het buitenland. Houd er rekening mee dat hierdoor de leveringsvoorwaarden, verzendtijden en/of het aankoopproces kunnen verschillen.
The Race Master / Alpha-X Holster utilizes an efficient and easy system to allow shooters to switch their holster from one gun type to another by means of changing the Insert Block Assembly. This switch is fast and easy and can be done in less than a minute, and without losing any of the holster’s adjustments or settings.
The Insert Block Assembly includes:
The Locking Block (gun specific).
The Sliding Lock, assembled (gun specific).
The safety lever, assembled.
The internal magnetic activation system, assembled.
“Magnetic logo” to cover over side hole in holsters which may still have it.
The Insert block grips the pistol only on the front end of the trigger guard, and a very precise fit is required in that area. In some cases, some light modifications to the Insert Block may be required.
Should you need to dismantle your insert block for some fitting, follow these steps:
Remove the insert block from the holster by removing the two small M4 screws from the back of the holster.
Using a punch and hammer, push the two steel pins from the front of the block towards the back (push from the side with the gun type engraved). These pins may be tight.
Once the pins are out, the plastic wedge holding the 2nd magnet will come out. Make sure the magnet does not fall out of the part. It is usually held snugly in its pocket.
Use a marker to make a dot on the top of the magnet which is embedded in the slide lock. This will make it easy for you to ensure that you reassemble it with the correct side up. Most likely it will fall out or you will want to remove it while fitting the slide lock.
To remove the slide lock from the block, unscrew the M3 screw visible from the back of the block – and then slide the slide lock upwards and out through the window in the block – passed the safety lever, which must be in the unlocked position.
To reassemble, reverse your steps.
The Race Master / Alpha-X Holster Insert Blocks are designed to be used in either RH or LH holsters. The same insert works for both.
Color: Black
* Trigger guard of CZ TS Czechmate very similar to that of the SP01, just a hair thicker.
Starting from 2017 year, the CZ TS Czechmate now uses the same frame as the CZ TS Orange. Note the thinner squarer trigger guard. A customer with this new model needs a TS Orange insert, (NOT a TS Czechmate insert), even though his gun is a CZ TS Czechmate.
