TTI Basis Pad voor STI/SV Magazines 4mm - Zwart

69,90 €

Vrij te koop (vanaf 18 jaar)

8700 Leoben, Oostenrijk

ID: 10086394

Dit aanbod is momenteel niet leverbaar.

Veilig kopen met Gunfinder

Onze AI-gestuurde identiteitsverificatie van verkopers maakt Gunfinder tot de veiligste marktplaats online. Meer weten

Over de verkoper

Earms

Dealer

3.748 advertenties

Details

Originele taal

Duits

Categorie

Staat

Nieuw

Locatie

🇦🇹 8700 Leoben, Oostenrijk

Beschikbaarheid

niet leverbaar

Actualiteit

Dit aanbod is gebaseerd op een aanbiedingssynchronisatie, waarbij de aanbiedingsgegevens vanuit een shop, handelaar of extern platform naar ons zijn overgedragen. Houd er rekening mee dat door mogelijke vertragingen bij de gegevensoverdracht tijdelijke prijsafwijkingen kunnen optreden.

Bron: Earms
Laatst bijgewerkt: ongeveer 8 uur geleden

Beschrijving

Opmerking: Het artikel bevindt zich in het buitenland. Houd er rekening mee dat hierdoor de leveringsvoorwaarden, verzendtijden en/of het aankoopproces kunnen verschillen.

The 4mm is our mid profile extension for the Staccato/Infinity/Springfield Prodigy/Atlas/Infinity 9/38 2011 style magazine. Although it will work on all 2011 style magazines, it is recommended for the 140mm magazine. It brings the capacity up from 20 rounds to 22 rounds with the factory spring and follower and still fits the USPSA 140mm gauge. If you want even more added capacity use our thin competition follower and extra power 11 coil spring to bump the capacity up to 23 rounds (but will not lock the slide to the rear on the last round fired). The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Magazine NOT included * For the Infinity Magazines: Our base pads will fit all the Infinity magazines and every generation. 9mm/38 – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 23+1 capacity. For Unlimited Division, we recommend the 170mm, the same 3mm extension must be used with our thin competition follower and 13 coil extra power spring to get 29+1 rounds and still fit the USPSA 170mm Gauge. Using a 140mm Magazine with our 7mm extension and our thin competition follower and 11 coil extra power spring will bump the capacity to 24+1. Recommended for the Unlimited Division. If you’re not buying any of this for competition, you can mix and match any of these magazines and pads for different endless combinations. .40SW – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 21+1 capacity. For the .40 Magazines: Staccato Magazines: without changing the spring and follower using our 4mm base pad will bump the capacity from 18 to 20 rounds and fit the 140mm USPSA gauge for limited. With our thin competition follower and 11 coil extra power spring it will hold 21 rounds. (but will not lock the slide to the rear on the last round fired Infinity: 140mm .40SW Magazines, the 3mm base pad and our thin competition follower and 11 coil extra power spring it will hold 21 rounds and still fit the 140mm gauge for USPSA/limited division. (but will not lock the slide to the rear on the last round fired Atlas Magazines: Using our 4mm base pad will allow the magazine to hold 18 rounds with the factory spring and follower. With our thin competition follower and 11 coil extra power spring it will bump the capacity from 18 rounds to 20 rounds. (but will not lock the slide to the rear on the last round fired). NOTE *Due to the variances in mag tube dimensions from different companies and even different generations of mags from the same company, the base pad may require minor fitting to the tube and the back of the lips may need the sharp edges buffed down so the mag will fit the gauge.*MADE IN THE USA

Afdrukken

TTI Basis Pad voor STI/SV Magazines 4mm - Zwart

Earms

Details

Actualiteit

Beschrijving

Dit vind je misschien ook interessant

Inkoopservice

Topveilingen

Inkoopservice

Gesponsorde aanbiedingen