DAA - 2-in-1 usadzovacia a krimpovacia matrica
≈ 31 €
Cena u predajcu: 349 kr. Prepočítané kurzom ECB zo dňa 13. November 2026.
Bez potreby povolenia (bez zbrojného preukazu)
254 64 Helsingborg, Švédsko
0
ID: 11617890
Nákup z krajiny mimo EÚ: Zbraň prejde cez dovozcu v tvojej krajine, predajca sa postará o vývoz.
Takto prebieha nákup z Európy
Nakupuj bezpečne s Gunfinder
Naše overovanie totožnosti predajcov pomocou umelej inteligencie robí z Gunfinder najbezpečnejšie online trhovisko.
Zistiť viac
Podrobnosti
- Pôvodný jazyk
- Švédčina
- Kategória
- Stav
- Nové
- Lokalita
- 🇸🇪 254 64 Helsingborg, Švédsko
- Dostupnosť
- dostupné
Aktuálnosť
Táto ponuka je prevzatá z obchodu, od predajcu alebo z externého trhoviska, odkiaľ k nám boli prenesené jej údaje. Upozorňujeme ťa, že v dôsledku možného oneskorenia pri prenose údajov sa ceny môžu dočasne líšiť.
- Zdroj
- RangeMaster Store
- Naposledy overené u predajcu
- pred približne 16 hodín
Popis
Upozornenie:
Tovar sa nachádza v zahraničí. Upozorňujeme, že dodacie podmienky, dodacie lehoty a/alebo postup nákupu sa preto môžu líšiť.
The answer to both questions is, YES, provided you combine your Seating and Crimping operations into one station, to free up the station your Bullet Feeder will need.
Such Seating and Crimping dies are available, and so we decided it was timer we made them directly available to our customers as well. We teamed up with one of the best Die manufacturers, LEE Precision, and are now pleased to offer you our DAA 2-in-1 Seating and crimping dies.
These quality stainless steel dies, enable you to Seat and Crimp in one station, without compromising the quality of your ammo. It may take a little longer to get the adjustments just right, but once calibrated correctly, this die will produce consistent and precise quality ammunition.
These dies include an O-ring lock machined into the nut, which allows you to hand tighten only – and the die stays put! They include a finger adjustable floating bullet Seater, are heat treated to ideal hardness and polished to the smoothest finish.
DAA 2-in-1 Seating & Crimping die – Set up Instructions
Thank you for choosing this DAA 2-in-1 Seating & Crimping die. This die frees up a station in your progressive-press tool head, making space for a bullet dropper die on your 550, or, allows you to use a bullet dropper along side a powder-check on your 650 or 1050.
Follow these steps to adjust the Die:
Position a well-sized and belled case in the appropriate station and run the tool head all the way down (or shell plate all the way up)
With the adjustment knob and lock ring on the die adjusted as high as they will go turn the die into the tool head until it stops, when the top of the case makes contact with the crimp shoulder.
Set the lock ring by turning it down until it locks against the top of the toolhead.
Turn the adjustment knob 2 full turns down, then lower the shell plate and place a bullet onto the case.
Keep turning the adjustment knob down, and test the length of the bullet until you get the overall length you are aiming for.
Once the correct length is reached, lower the shell plate, and loosen the lock ring. Then, turn the die down another half turn to create an adequate crimp, and retighten the lock ring. Then turn the adjustment knob about 2 turns out.
Raise the shell plate again and bring the bullet back into the die, then turn the adjustment knob down until it makes contact with the top of the bullet.
Now the die is properly set for both depth and crimp, which occur at the same time at the top of the stroke.
