Achtung:
Twoja przeglądarka jest przestarzała. Z tego powodu Gunfinder może nie działać poprawnie w niektórych miejscach. Jak najszybciej zaktualizuj przeglądarkę. Dowiedz się więcej!
Ta oferta pochodzi z synchronizacji danych, podczas której informacje o ofercie zostały przesłane do nas ze sklepu, sprzedawcy lub zewnętrznego marketplace'u. Pamiętaj, że ze względu na możliwe opóźnienia w przesyłaniu danych mogą wystąpić tymczasowe różnice w cenach.
Źródło
Corax Store
Ostatnio sprawdzono u sprzedawcy
około 3 godziny temu
Opis
Uwaga:
Przedmiot znajduje się za granicą. Pamiętaj, że warunki dostawy, czas wysyłki i/lub procedura zakupu mogą się różnić.
Fix the dreaded 'gun rattle' when you run or otherwise move around your day.
Sized small enough for the Safariland® 7377 holsters for compact lights such as the TLR-7, XC1, or APLc, but big enough it can also be used in Full size light holsters (X300, TLR-1 etc). Provides for a completely consistent position of the gun in the holster as some setups can vary almost 1/4", making your draw more consistent as well.
How to use: Watch YouTube video for simple demo- and/or read below:
Compact light holsters: Place in holster adhesive backing down, place gun in holster, leave it for a few hours to allow the foam to take memory to the light. Draw from the holster, checking for the level of pressure against the ALS mechanism. If it is too tight for your liking, trim the foam with scissors by slightly less than 1/8". Recheck. Remove adhesive backing, stick pencil in foam and gently place it in the base of your holster, careful not to cover the drainage hole. That's it.
Full Size light holsters: If you have a holster that you can see through the bottom of the holster (older 7TS and all 6000 series), you can measure the distance between the light and the base of the holster, with the gun pushed all the way up against the ALS® mechanism. One piece of foam is .625". Depending on your light/gun combo, you may need just one and will trim it, or you may need to get two or three and stick them together.
If possible, with an UN-loaded weapon, measure up through the base of the holster until you hit the light. Add just over .25" and insert that much foam.
Amount needed varies by holster model...New 7TS holsters you cannot see through the base, so you will need to do some trial and error. Be a responsible adult, once you apply one of these with the adhesive, it will not come out easily.
Fix the dreaded 'gun rattle' when you run or otherwise move around your day. Sized small enough for the Safariland® 7377 holsters for compact lights such as the TLR-7, XC1, or APLc, but big enough it can also be used in Full size light holsters (X300, TLR-1 etc). Provides for a completely consistent position of the gun in the holster as some setups can vary almost 1/4", making your draw more consistent as well.
How to use: Watch YouTube video for simple demo- and/or read below:
Compact light holsters: Place in holster adhesive backing down, place gun in holster, leave it for a few hours to allow the foam to take memory to the light. Draw from the holster, checking for the level of pressure against the ALS mechanism. If it is too tight for your liking, trim the foam with scissors by slightly less than 1/8". Recheck. Remove adhesive backing, stick pencil in foam and gently place it in the base of your holster, careful not to cover the drainage hole. That's it.
Full Size light holsters: If you have a holster that you can see through the bottom of the holster (older 7TS and all 6000 series), you can measure the distance between the light and the base of the holster, with the gun pushed all the way up against the ALS® mechanism. One piece of foam is .625". Depending on your light/gun combo, you may need just one and will trim it, or you may need to get two or three and stick them together.
If possible, with an UN-loaded weapon, measure up through the base of the holster until you hit the light. Add just over .25" and insert that much foam.
Amount needed varies by holster model...New 7TS holsters you cannot see through the base, so you will need to do some trial and error. Be a responsible adult, once you apply one of these with the adhesive, it will not come out easily.
Za twoją zgodą rozpoznajemy twoją przeglądarkę przy kolejnej wizycie i widzimy, czego myśliwi i strzelcy naprawdę szukają. Dzięki temu każdego dnia ulepszamy wyszukiwanie i ofertę oraz pokazujemy ci więcej tego, co cię interesuje. Twoje dane pozostają u nas: nie udostępniamy ich ani nie sprzedajemy.
Swoją decyzję możesz zmienić w dowolnym momencie, klikając link Ustawienia plików cookie w stopce strony. Informacje o tym, co zapisujemy, znajdziesz w Polityce prywatności.
Ustawienia plików cookie
Logowanie, lista życzeń, język i funkcje bezpieczeństwa. Zapewniają one prawidłowe działanie Gunfinder i dlatego są zawsze aktywne.
Jeśli wyrazisz zgodę, rozpoznamy twoją przeglądarkę przy następnej wizycie i lepiej zrozumiemy, czego naprawdę szukają myśliwi i strzelcy. Pomoże nam to każdego dnia ulepszać wyszukiwanie i ofertę. W tym celu zapisujemy na twoim urządzeniu losowy identyfikator, ważny przez dwa lata i niezawierający żadnych danych osobowych. Bez zgody zliczamy dane wyłącznie anonimowo. Czy twój profil ma również wpływać na to, co widzisz, możesz wybrać za pomocą następnego przełącznika.
Jeśli wyrazisz zgodę, wykorzystamy Twój profil, aby pokazywać Ci na Gunfinder oferty i treści dopasowane do Twoich zainteresowań: więcej tego, co naprawdę Cię interesuje, mniej przypadkowych treści. Nic nie zostanie przy tym ukryte. Wymaga to zgody na statystyki – bez niej profil nie powstanie. W ramach kontroli skuteczności nieliczni użytkownicy, którzy wyrazili zgodę, losowo widzą widok niespersonalizowany. Twój profil pozostaje u nas.
Pliki cookie są wyłączone
Twoja przeglądarka nie zezwala na pliki cookie. Nie możemy więc zapisać twojego wyboru ani o niego pytać — działa tylko to, co jest niezbędne do funkcjonowania strony. Funkcje takie jak logowanie czy lista ulubionych wymagają jednak plików cookie i pozostaną wyłączone.