DAA Mini Mr.Bulletfeeder od DAA - Pistolet
≈ 140 €
Cena u Dealera: 130 CHF. Przeliczono po kursie EBC z 16 października 2026.
Do nabycia bez pozwolenia (od 18 lat)
9200 Gossau SG, Szwajcaria
0
ID: 10786116
Zakup spoza UE: Broń przechodzi przez importera w twoim kraju, a sprzedawca zajmuje się eksportem.
Tak przebiega zakup z Europy
Bezpieczne zakupy z Gunfinder
Nasze weryfikowanie tożsamości sprzedawców wspierane przez AI czyni Gunfinder najbezpieczniejszym marketplace'em online.
Dowiedz się więcej
Szczegóły
- Język oryginalny
- Niemiecki
- Kategoria
- Stan
- Nowe
- Lokalizacja
- 🇨🇭 9200 Gossau SG, Szwajcaria
- Dostępność
- ograniczona dostępność
Aktualność
Ta oferta pochodzi z synchronizacji danych, podczas której informacje o ofercie zostały przesłane do nas ze sklepu, sprzedawcy lub zewnętrznego marketplace'u. Pamiętaj, że ze względu na możliwe opóźnienia w przesyłaniu danych mogą wystąpić tymczasowe różnice w cenach.
- Źródło
- Shop Indoorswiss
- Ostatnia aktualizacja
- około 16 godzin temu
Opis
Uwaga:
Przedmiot znajduje się za granicą. Pamiętaj, że warunki dostawy, czas wysyłki i/lub procedura zakupu mogą się różnić.
The Dillon XL750 Powder Measure is angled such that the powder bar must extend directly over station #4 in the toolhead, and it cannot be repositioned. This Is not an issue if you have a short die in that station. However, if you wish to run a powder check in station #3, and a bullet dropper in station #4, as many do, this creates a serious problem.
As a solution to this issue we are pleased to offer our Extra-Short Dillon Powder Bar.
The Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder.
Using a Mr.Bulletfeeder while reloading is a real pleasure. It makes the reloading process faster and much easier. If you have never used one, you are missing out on one of the greatest reloading assists out there! A Bulletfeeder also improves safety, by preventing the need to insert your fingers under the tool head to place your bullets on the brass. Everyone should use one!
The problem of course, is cost. Shooting is expensive, and reloading ammo, while usually cheaper than shooting factory, is not as cheap as it once was…
You need to buy a press, other reloading accessories, not to mention ammo components. For many, by the time all that is purchased, they have stretched their budget about as far as it will go. And the Bulletfeeder gets passed on, for lack of funds.
This was our motivation when setting out to develop a less expensive version of the Mr.Bulletfeeder, and it lead to the new Mini Mr.Bulletfeeder.
Each magazine of bullet tubes needs to be filled by hand before reloading, much in the same way you would fill your primer tubes before starting your reloading session. With a little practice, it will take you about 2 minutes to fill the tube assembly. And this can be done in advance while watching TV in the comfort of your living room. Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting your reloading session.
While reloading, you will see the bullets drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue without delay.
The Mini Mr.Bulletfeeder can be used on any progressive reloading machine which uses the same size dies as Dillon, however please note that the powder funnel we supply with the unit is designed to be used only in the Dillon powder drop! If you wish to use the Mini Mr.Bulletfeeder with another press, you may need to get another powder funnel to expand the brass.
Be aware that the bullet feeder does require a station in your tool head, directly after the powder dropper.
We have found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to do with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050.
Your Mini Mr.Bulletfeeder by DAA includes:
1 x 6-Tube Bullet Magazine Assembly
1 x Dropper Die Assembly
1 x Expanding powder funnel (Dillon compatible)
3 x Spare Steel Ball-Bearings for Dropper
1 x User Instruction Sheet
Please note: Mr.Bullet feeders and Mini Mr.BF are usually shipped with our Dillon Powder funnel. If you wish us to swap that out for a Hornady funnel when shipping – we can do so for you. request that at time of ordering.
