TTI Podstawa do magazynków STI/SV 7mm - Czarny

69,90 €

Do nabycia bez pozwolenia (od 18 lat)

8700 Leoben, Austria

ID: 10085113

Ta oferta jest obecnie niedostępna.

Bezpieczne zakupy z Gunfinder

Nasze weryfikowanie tożsamości sprzedawców wspierane przez AI czyni Gunfinder najbezpieczniejszym marketplace'em online. Dowiedz się więcej

O sprzedającym

Earms

Sprzedawca

3 748 ogłoszeń

Szczegóły

Język oryginalny

Niemiecki

Kategoria

Stan

Nowe

Lokalizacja

🇦🇹 8700 Leoben, Austria

Dostępność

niedostępny

Aktualność

Ta oferta pochodzi z synchronizacji danych, podczas której informacje o ofercie zostały przesłane do nas ze sklepu, sprzedawcy lub zewnętrznego marketplace'u. Pamiętaj, że ze względu na możliwe opóźnienia w przesyłaniu danych mogą wystąpić tymczasowe różnice w cenach.

Źródło: Earms
Ostatnia aktualizacja: około 7 godzin temu

Opis

Uwaga: Przedmiot znajduje się za granicą. Pamiętaj, że warunki dostawy, czas wysyłki i/lub procedura zakupu mogą się różnić.

The 7mm is our longest extension for the Staccato/Infinity/Springfield Prodigy/Atlas/Infinity/MBX 9/38 2011 style magazine and Bul Armory SAS II Pistols. Although it will work with all 2011 style magazines it is recommended for the 140mm Magazines for Open/Unlimited division and the 126mm because that’s what John Wick will do. On the 140mm magazine, the 7mm extension bumps the capacity from 20 rounds to 22 rounds with the factory spring and follower. For even more added capacity, use our thin competition follower and extra power 11 coil spring for an impressive 24 round capacity (but will not lock the slide to the rear on the last round fired). The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Magazine NOT included * For the Infinity Magazines: Our base pads will fit all the Infinity magazines and every generation. 9mm/38 – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 23+1 capacity. For Unlimited Division, we recommend the 170mm, the same 3mm extension must be used with our thin competition follower and 13 coil extra power spring to get 29+1 rounds and still fit the USPSA 170mm Gauge. Using a 140mm Magazine with our 7mm extension and our thin competition follower and 11 coil extra power spring will bump the capacity to 24+1. Recommended for the Unlimited Division. If you’re not buying any of this for competition, you can mix and match any of these magazines and pads for different endless combinations. .40SW – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 21+1 capacity. For the .40 Magazines: Staccato Magazines: without changing the spring and follower using our 4mm base pad will bump the capacity from 18 to 20 rounds and fit the 140mm USPSA gauge for limited. With our thin competition follower and 11 coil extra power spring it will hold 21 rounds. (but will not lock the slide to the rear on the last round fired Infinity: 140mm .40SW Magazines, the 3mm base pad and our thin competition follower and 11 coil extra power spring it will hold 21 rounds and still fit the 140mm gauge for USPSA/limited division. (but will not lock the slide to the rear on the last round fired Atlas Magazines: Using our 4mm base pad will allow the magazine to hold 18 rounds with the factory spring and follower. With our thin competition follower and 11 coil extra power spring it will bump the capacity from 18 rounds to 20 rounds. (but will not lock the slide to the rear on the last round fired). NOTE *Due to the variances in mag tube dimensions from different companies and even different generations of mags from the same company, the base pad may require minor fitting to the tube and the back of the lips may need the sharp edges buffed down so the mag will fit the gauge.*MADE IN THE USA

Drukuj

TTI Podstawa do magazynków STI/SV 7mm - Czarny

Earms

Szczegóły

Aktualność

Opis

To może cię również zainteresować

Usługa skupu

Top aukcje

Usługa skupu

Oferty sponsorowane