MINI MR BULLETFEEDER BY DAA 9MM / 38 SUPER AUTO
129 €
De libre adquisición (a partir de 18 años)
4240 Freistadt, Austria
1
ID: 10098749
Esta oferta no está disponible actualmente.
Compra seguro con Gunfinder
Nuestra verificación de identidad impulsada por IA hace que Gunfinder sea el marketplace más seguro online.
Más información
Detalles
- Idioma original
- Alemán
- Categoría
- Estado
- Nuevo
- Ubicación
- 🇦🇹 4240 Freistadt, Austria
- Disponibilidad
- no disponible
Actualidad
Esta oferta se basa en una sincronización de datos, mediante la cual la información de la oferta se ha transferido a nuestra plataforma desde una tienda, distribuidor o marketplace externo. Ten en cuenta que pueden producirse diferencias de precio temporales debido a posibles retrasos en la transferencia de datos.
- Fuente
- Shootingstore
- Última actualización
- hace aproximadamente 3 horas
Descripción
Nota:
El artículo se encuentra en el extranjero. Ten en cuenta que las condiciones de entrega, los plazos de envío y/o el proceso de compra pueden variar.
The Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder.
Using a Mr.Bulletfeeder while reloading is a real pleasure. It makes the reloading process faster and much easier. If you have never used one, you are missing out on one of the greatest reloading assists out there! A Bulletfeeder also improves safety, by preventing the need to insert your fingers under the tool head to place your bullets on the brass. Everyone should use one!
The problem of course, is cost. Shooting is expensive, and reloading ammo, while usually cheaper than shooting factory, is not as cheap as it once was…
You need to buy a press, other reloading accessories, not to mention ammo components. For many, by the time all that is purchased, they have stretched their budget about as far as it will go. And the Bulletfeeder gets passed on, for lack of funds.
This was our motivation when setting out to develop a less expensive version of the Mr.Bulletfeeder, and it lead to the new Mini Mr.Bulletfeeder.
Each magazine of bullet tubes needs to be filled by hand before reloading, much in the same way you would fill your primer tubes before starting your reloading session. With a little practice, it will take you about 2 minutes to fill the tube assembly. And this can be done in advance while watching TV in the comfort of your living room. Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting your reloading session.
While reloading, you will see the bullets drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue without delay.
The Mini Mr.Bulletfeeder can be used on any progressive reloading machine which uses the same size dies as Dillon, however please note that the powder funnel we supply with the unit is designed to be used only in the Dillon powder drop! If you wish to use the Mini Mr.Bulletfeeder with another press, you may need to get another powder funnel to expand the brass.
Be aware that the bullet feeder does require a station in your tool head, directly after the powder dropper.
We have found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to do with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050.
Your Mini Mr.Bulletfeeder by DAA includes:
1 x 6-Tube Bullet Magazine Assembly
1 x Dropper Die Assembly
1 x Expanding powder funnel (Dillon compatible)
3 x Spare Steel Ball-Bearings for Dropper
1 x User Instruction Sheet
